Specifications for Removing and Replacing Damaged Cementitious Roof Deck Panels Page 1 of 5 Procedures Step 1: Determine the system: a Plank with T and G sides and self support between purlins. b Tile with support on sides with Bulb or Truss Tees. Check center to center of Bulb Tees and edge to edge. Tectum tiles must have 1/2 minimum bearing
deck substrates, such as cement wood fiber, gyp-sum and insulation concretes. The TL Tectum and Lightweight Fastener can even be installed through old B.U.R. into tectum without pre-drilling. The TL Tectum and Lightweight Fastener System has many benefits you will find valuable when working with lightweight roof decks. Some of them are as follows:
NRDCA 500 Gypsum Roof Deck Replacement Procedures* Gypsum concrete Wire Mesh Formboard Bulb or Truss Tee History Gypsum cast over formboards and structurally supported by bulb tees or truss tees was introduced as a roof deck substrate in the 1940s. This system provides fire resistance, seismic
Tectum I Roof Deck Panel, Available in 2", 2-1/2" or 3" Thickness Tectum I is typically used in low-slope applications and provides a thermal barrier for field-applied foam plastics. It is compatible with virtually all roof installation materials.
Roof Decking Systems Commercial and Industrial Roofing Products in West Chester, PA Corrugated Metal Deck , concrete planks or slabs, Acoustic deck, Gypsum repairs, Fiberglass deck - whatever the need, Long and O'Rourke can service your requirement.
most important. With the variety of decks to be encountered both new and old , it is incumbent upon rooing experts to be the authority on these matters. This article will explore features of structural cement iber roof decks. INTRODUCTION A number of systems have been offered by vendors, including Tectum, by Tectum,
Today my crew tore-off a roof and there was some damage to the decking. When they tore it out it was 3" thick and looked like pressed hay or st. I called every distributor in my area and discovered it was called Tectum Decking, most had heard of it but none had it in stock.
Cement-Wood Fiber Panel Roof Deck Tectum Cement-wood fiber roof deck panels are composed of treated wood fibers that are bounded together with Portland cement or other binder and compressed or molded into flat panels. The panels provide both acoustical and thermal insulation.
Tectum Roof Deck Panels provide a number of cost-effective advantages, including ease-of-installation, a nailable top surface for direct application of the roof, and an abuse-resistant, acoustical-textured interior finish, all in one easy-to-install panel.
TECTUM Roof Deck Armstrong Building Solutions. Composite roof deck solution with good sound absorption, R-values up to 36, for long span applications up to 12 feet. TECTUM III and TECTUM IIIP Composite roof deck solution with good sound absorption, R-values up to 44, and high humidity application performance.Continue reading
Tectum E and Tectum E-N Acoustical Roof Deck The Tectum E roof deck panel is a composite of a 1½ or thicker Tectum substrate, EPS expanded polystyrene insulation and 7/16 OSB sheathing with a slip-resistant surface. The EPS core exceeds the requirements of ASTM C-578 Type I and bears the UL classification mark.
Condition of the roof deck is it corroded, detached, damaged or unsafe? Has the deck been deformed or deflected to the point where it ponds water? FIG 4 Is the deck capable of handling a heavier roof system, such as replacing a built-up roof membrane 4-10 psf with a ballasted single-ply system 10-20 psf ?
22070 Replace Tectum decking, 2.5" thickness SF $12.80 $10.88 22071 Replace Tectum decking, 3" thickness SF $14.27 $12.13 22072 Replace concrete plank or panel roof decking SF $12.80 $10.88 22073 Replace pre-cast "Flexcore" concrete roof decking SF 22074 Replace pre-cast double"T" concrete roof decking SF
TECTUM III and TECTUM IIIP Composite roof deck solution with good sound absorption, R-values up to 44, and high humidity application performance. TECTUM E and TECTUM E-N Composite roof deck solution with excellent sound absorption, R-values up to 43, with EPS or GPS insulation options.
Tectum IIIP Roof Deck Panels can be repaired and replaced by taking the following steps: 1. Cut out existing full span and full panel width. 2. Make vertical cut around the perimeter of panel leaving the spline and Tongue and Groove in place. 3. The replacement Tectum IIIP pan els should be 47 wide beveled on all four sides and square ends. 4.
- Synthetic Teak Decking
- Outdoor Wall Panel
- Ecological WPC Floor
- Best DIY Decking
- Impact Resistance PVC Fence
- Waterproof WPC Pergola
- Outdoor Other Products
- Boat Deck Install step
- Wall Panel Install step
- WPC Floor Install step
- DIY Decking Install step
- PVC Fence Install step
- WPC Fence Install step
Other Products Case:
- engineered decking lumber prices
- pressure treated fence boards shrink
- deck railing post inside rim joist
- replace marine wood with plastic
- china mosaic flooring for terrace
- 2 story covered deck plans
- caribbean fencing design
- how to make a wheelbarrow bench
- easy install teak flooring boat
- natural timber ash peel and stick floor tiles
- outdoor gazebo new zealand
- 625 sq ft deck boards Singapore
- plastic slats for a park bench
- frost proof balcony materials for the arts
- non flammable back boards texas
- furniture with left over wood
- severe weather white composite railing
- 2018 new nice wood plastic composite outdoor flooring
- cheapest wall cladding sale
- exterior cladding panels manufacturer definition
- railing vertical spacing
- folding wooden deck chairs
- Price Of Recycled PVC Fence Materials
- importers fencing panels from italy
- cheap pave laminate wood online sales
- designer series wall panels
- low cost privacy composite fencing options